Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- mk3:quick_start_guide [2025/04/07 14:42] – grnbms_tech
+++ mk3:quick_start_guide [2025/04/07 19:02] (aktuell) – [2. Network Connection] grnbms_tech
@@ Zeile 1: / Zeile 1: @@
+===== GRNbms MK3 Quick Start Guide =====
 ==== 1. Power Supply ====
 The GRNbms MK3 supports both **High Voltage (HV)** and **Low Voltage (LV)** operation.
 === ➤ Low Voltage Mode (12 V System) ===
+{{:mk3:screenshot_2025-04-07_163618.png?nolink&162x162}}
   * Connect 12 V to the **"Jump Start"**  connector
   * This powers the BMS directly for low-voltage applications or setup/configuration
-{{:mk3:screenshot_2025-04-07_163618.png?nolink&162x162}}
+''👉 Details about relay and output wiring can be found [[:mk3:lvrelays|here]]''
 === ➤ High Voltage Mode ===
+''{{:mk3:screenshot_2025-04-07_163636.png?nolink&460x130}}''
   * For high-voltage setups, connect the BMS using the dedicated **HV connectors**
@@ Zeile 30: / Zeile 35: @@
   * Use a **dual connection**  if possible for redundancy
-''👉 Details about relay and output wiring can be found''
+''👉 Details about relay and output wiring can be found [[:mk3:hvrelaywirring|here]]''
+====   ====
+====   ====
+==== 2. Network Connection ====
+An internet connection is required for the **initial setup** and activation of your BMS.
+''📝 **Note:** A [[https://grnbms.de|GRNbms.de]] account is required to complete the setup.\\
+You can create one during the initial configuration or in advance here.''
+=== ➤ Ethernet Connection (recommended) ===
+  * Connect the BMS (ETHERNET 1 Connector) to your local network using a **standard RJ45 Ethernet cable**
+  * The BMS will automatically obtain an IP address via **DHCP**  (from your router)
+=== ➤ WLAN (optional) ===
+If no Ethernet is available, the BMS can create a **WiFi access point**:
+  * Plug in a **compatible USB WiFi stick****before power-on**
+  * ''✅ Must be a supported chip – see [[:mk3:compatible_wifi_sticks_list|compatible WiFi sticks list]]''
+The BMS will create a hotspot:
+  * **SSID: **''GRNbms_MK3_AP''
+  * **Password: **''0123456789''
+  * **IP Address: **''192.168.4.1''
+Connect to the hotspot and open ''[[http://192.168.4.1|http://192.168.4.1]]''to start setup.
+=== ➤ Accessing the BMS ===
+Once connected, try opening one of the following in your browser:
+  * ''[[http://grnbmsmk3/|http://grnbmsmk3/]]''
+  * ''[[http://grnbmsmk3.local/|http://grnbmsmk3.local/]]''
+''💡 These names work only if your router supports mDNS or local hostname resolution.''
+=== ➤ Can’t find your BMS? ===
+No problem – just visit ''[[https://grnbms.de|GRNbms.de]]'' \\ There you can see all BMS devices in your local network.
+====   ====
+====   ====
+==== 3. Initial Setup Wizard ====
+When you access the BMS interface for the first time, a guided setup will begin automatically.
+=== ➤ Step 1: Network Connection ===
+If no internet connection is available, the BMS will first ask you to connect it to the internet (via Ethernet or WLAN).
+=== ➤ Step 2: Login ===
+Once online, you will be prompted to log in with your [[https://grnbms.de|GRNbms.de]] account.
+''🧑‍💼 The first user to log in will automatically become the **owner**  of this BMS system.''
+=== ➤ Step 3: Software Update ===
+If a firmware update is available, the BMS will guide you through the update process before proceeding.
+=== ➤ Final: Dashboard ===
+After completing all steps, you will be redirected to the **main overview page**, where you can continue configuration.
-Schritt 2
+''🔐 To make further changes, you need to **log in again**  via the login button in the top right corner of the web interface.''